[Contrib] [RFC Index] [RFC 1800 - 1899]    RFC 1850: OSPF Version 2 Management Information Base

RFC 1850: OSPF Version 2 Management Information Base   Network Working Group F. Baker Request For Comments: 1850 Cisco Systems Obsoletes: 1253 R. Coltun Category: Standards Track RainbowBridge Communications November 1995 OSPF Version 2 Management Information Base Status of this Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in TCP/IP-based internets. In particular, it defines objects for managing the Open Shortest Path First Routing Protocol. Table of Contents 1. The SNMPv2 Network Management Framework .............. 2 1.1 Object Definitions .................................. 3 2. Overview ............................................. 3 2.1 Changes from RFC 1253 ............................... 3 2.2 Textual Conventions ................................. 6 2.3 Structure of MIB .................................... 6 2.3.1 General Variables ................................. 6 2.3.2 Area Data Structure and Area Stub Metric Table .... 7 2.3.3 Link State Database and External Link State Database .......................................... 7 2.3.4 Address Table and Host Tables ..................... 7 2.3.5 Interface and Interface Metric Tables ............. 7 2.3.6 Virtual Interface Table ........................... 7 2.3.7 Neighbor and Virtual Neighbor Tables .............. 7 2.4 Conceptual Row Creation ............................. 7 2.5 Default Configuration ............................... 8 3. Definitions .......................................... 10 3.1 OSPF General Variables .............................. 13 3.2 OSPF Area Table ..................................... 17 Baker & Coltun Standards Track [Page 1] RFC 1850 OSPF MIB November 1995 3.3 OSPF Area Default Metrics ........................... 21 3.4 OSPF Link State Database ............................ 25 3.5 OSPF Address Range Table ............................ 27 3.6 OSPF Host Table ..................................... 29 3.7 OSPF Interface Table ................................ 32 3.8 OSPF Interface Metrics .............................. 39 3.9 OSPF Virtual Interface Table ........................ 42 3.10 OSPF Neighbor Table ................................ 46 3.11 OSPF Virtual Neighbor Table ........................ 51 3.12 OSPF External Link State Database .................. 54 3.13 OSPF Route Table Use ............................... 57 3.14 OSPF Area Aggregate Table .......................... 58 4. OSPF Traps ........................................... 66 4.1 Format Of Trap Definitions .......................... 67 4.2 Approach ............................................ 67 4.3 Ignoring Initial Activity ........................... 67 4.4 Throttling Traps .................................... 67 4.5 One Trap Per OSPF Event ............................. 68 4.6 Polling Event Counters .............................. 68 5. OSPF Trap Definitions ................................ 69 5.1 Trap Support Objects ................................ 69 5.2 Traps ............................................... 71 6. Acknowledgements ...................................... 78 7. References ............................................ 78 8. Security Considerations ............................... 80 9. Authors' Addresses .................................... 80 1. The SNMPv2 Network Management Framework The SNMPv2 Network Management Framework consists of four major components. They are: o RFC 1441 which defines the SMI, the mechanisms used for describing and naming objects for the purpose of management. o STD 17, RFC 1213 defines MIB-II, the core set of managed objects for the Internet suite of protocols. o RFC 1445 which defines the administrative and other architectural aspects of the framework. o RFC 1448 which defines the protocol used for network access to managed objects. The Framework permits new objects to be defined for the purpose of experimentation and evaluation. Baker & Coltun Standards Track [Page 2] RFC 1850 OSPF MIB November 1995 1.1. Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to refer to the object type. 2. Overview 2.1. Changes from RFC 1253 The changes from RFC 1253 are the following: (1) The textual convention PositiveInteger was changed from 1..'FFFFFFFF'h to 1..'7FFFFFFF'h at the request of Marshall Rose. (2) The textual convention TOSType was changed to reflect the TOS values defined in the Router Requirements Draft, and in accordance with the IP Forwarding Table MIB's values. (3) The names of some objects were changed, conforming to the convention that an acronym (for example, LSA) is a single word ("Lsa") in most SNMP names. (4) textual changes were made to make the MIB readable by Dave Perkins' SMIC MIB Compiler in addition to Mosy. This involved changing the case of some characters in certain names and removing the DEFVAL clauses for Counters. (5) The variables ospfAreaStatus and ospfIfStatus were added, having been overlooked in the original MIB. (6) The range of the variable ospfLsdbType was extended to include multicastLink (Group-membership LSA) and nssaExternalLink (NSSA LSA). (7) The variable ospfIfMetricMetric was renamed ospfIfMetricValue, and the following text was removed from its description: "The value FFFF is distinguished to mean 'no route via Baker & Coltun Standards Track [Page 3] RFC 1850 OSPF MIB November 1995 this TOS'." (8) The variable ospfNbmaNbrPermanence was added, with the values 'dynamic' and 'permanent'; by this means, dynamically learned and configured neighbors can be distinguished. (9) The DESCRIPTION of the variable ospfNbrIpAddr was changed from "The IP address of this neighbor." to "The IP address this neighbor is using in its IP Source Address. Note that, on addressless links, this will not be 0.0.0.0, but the address of another of the neighbor's interfaces." This is by way of clarification and does not change the specification. (10) The OSPF External Link State Database was added. The OSPF Link State Database used to display all LSAs stored; in this MIB, it displays all but the AS External LSAs. This is because there are usually a large number of External LSAs, and they are relicated in all non-Stub Areas. (11) The variable ospfAreaSummary was added to control the import of summary LSAs into stub areas. If it is noAreaSummary (default) the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its default route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs. (12) The general variables ospfExtLsdbLimit and ExitOverflowInterval were introduced to help handle LSDB overflow. (13) The use of the IP Forwarding Table is defined. (14) The ospfAreaRangeTable was obsoleted and replaced with the ospfAreaAggregateTable to accommodate two additional indexes. The ospfAreaAggregateEntry keys now include a LsdbType (which can be used to differentiate between the traditional type-3 Aggregates and NSSA Aggregates) and an Baker & Coltun Standards Track [Page 4] RFC 1850 OSPF MIB November 1995 ospfAreaAggregateMask (which will more clearly express the range). (15) The variable ospfAreaAggregateEffect was added. This permits the network manager to hide a subnet within an area. (16) Normally, the border router of a stub area advertises a default route as an OSPF network summary. An NSSA border router will generate a type-7 LSA indicating a default route, and import it into the NSSA. ospfStubMetricType (ospf internal, type 1 external, or type 2 external) indicates the type of the default metric advertised. (17) ospfMulticastExtensions is added to the OSPF General Group. This indicates the router's ability to forward IP multicast (Class D) datagrams. (18) ospfIfMulticastForwarding is added to the Interface Group. It indicates whether, and if so, how, multicasts should be forwarded on the interface. (19) The MIB is converted to SNMP Version 2. Beyond simple text changes and the addition of the MODULE-IDENTITY and MODULE-COMPLIANCE macros, this involved trading the TruthValue Textual Convention for SNMP Version 2's, which has the same values, and trading the Validation Textual Convention for SNMP Version 2's RowStatus. (20) ospfAuthType (area authentication type) was changed to an interface authentication type to match the key. It also has an additional value, to indicate the use of MD5 for authentication. (21) ospfIfIntfType has a new value, pointToMultipoint. (22) ospfIfDemand (read/write) is added, to permit control of Demand OSPF features. (23) ospfNbrHelloSuppressed and ospfVirtNbrHelloSuppressed were added, (read only). They indicate whether Hellos are being suppressed to the neighbor. (24) ospfDemandExtensions was added to indicate whether the Demand OSPF extensions have been implemented, and to disable them if appropriate. Baker & Coltun Standards Track [Page 5] RFC 1850 OSPF MIB November 1995 2.2. Textual Conventions Several new data types are introduced as a textual convention in this MIB document. These textual conventions enhance the readability of the specification and can ease comparison with other specifications if appropriate. It should be noted that the introduction of the these textual conventions has no effect on either the syntax nor the semantics of any managed objects. The use of these is merely an artifact of the explanatory method used. Objects defined in terms of one of these methods are always encoded by means of the rules that define the primitive type. Hence, no changes to the SMI or the SNMP are necessary to accommodate these textual conventions which are adopted merely for the convenience of readers and writers in pursuit of the elusive goal of clear, concise, and unambiguous MIB documents. The new data types are AreaID, RouterID, TOSType, Metric, BigMetric, Status, PositiveInteger, HelloRange, UpToMaxAge, InterfaceIndex, and DesignatedRouterPriority. 2.3. Structure of MIB The MIB is composed of the following sections: General Variables Area Data Structure Area Stub Metric Table Link State Database Address Range Table Host Table Interface Table Interface Metric Table Virtual Interface Table Neighbor Table Virtual Neighbor Table External Link State Database Aggregate Range Table There exists a separate MIB for notifications ("traps"), which is entirely optional. 2.3.1. General Variables The General Variables are about what they sound like; variables which are global to the OSPF Process. Baker & Coltun Standards Track [Page 6] RFC 1850 OSPF MIB November 1995 2.3.2. Area Data Structure and Area Stub Metric Table The Area Data Structure describes the OSPF Areas that the router participates in. The Area Stub Metric Table describes the metrics advertised into a stub area by the default router(s). 2.3.3. Link State Database and External Link State Database The Link State Database is provided primarily to provide detailed information for network debugging. 2.3.4. Address Table and Host Tables The Address Range Table and Host Table are provided to view configured Network Summary and Host Route information. 2.3.5. Interface and Interface Metric Tables The Interface Table and the Interface Metric Table together describe the various IP interfaces to OSPF. The metrics are placed in separate tables in order to simplify dealing with multiple types of service, and to provide flexibility in the event that the IP TOS definition is changed in the future. A Default Value specification is supplied for the TOS 0 (default) metric. 2.3.6. Virtual Interface Table Likewise, the Virtual Interface Table describe virtual links to the OSPF Process. 2.3.7. Neighbor and Virtual Neighbor Tables The Neighbor Table and the Virtual Neighbor Table describe the neighbors to the OSPF Process. 2.4. Conceptual Row Creation For the benefit of row-creation in "conceptual" (see [9]) tables, DEFVAL (Default Value) clauses are included in the definitions in section 3, suggesting values which an agent should use for instances of variables which need to be created due to a Set-Request, but which are not specified in the Set-Request. DEFVAL clauses have not been specified for some objects which are read-only, implying that they are zeroed upon row creation. These objects are of the SYNTAX Counter32 or Gauge32. For those objects not having a DEFVAL clause, both management stations and agents should heed the Robustness Principle of the Baker & Coltun Standards Track [Page 7] RFC 1850 OSPF MIB November 1995 Internet (see RFC-791): "be liberal in what you accept, conservative in what you send" That is, management stations should include as many of these columnar objects as possible (e.g., all read-write objects) in a Set-Request when creating a conceptual row; agents should accept a Set-Request with as few of these as they need (e.g., the minimum contents of a row creating SET consists of those objects for which, as they cannot be intuited, no default is specified.). There are numerous read-write objects in this MIB, as it is designed for SNMP management of the protocol, not just SNMP monitoring of its state. However, in the absence of a standard SNMP Security architecture, it is acceptable for implementations to implement these as read-only with an alternative interface for their modification. 2.5. Default Configuration OSPF is a powerful routing protocol, equipped with features to handle virtually any configuration requirement that might reasonably be found within an Autonomous System. With this power comes a fair degree of complexity, which the sheer number of objects in the MIB will attest to. Care has therefore been taken, in constructing this MIB, to define default values for virtually every object, to minimize the amount of parameterization required in the typical case. That default configuration is as follows: Given the following assumptions: - IP has already been configured - The ifTable has already been configured - ifSpeed is estimated by the interface drivers - The OSPF Process automatically discovers all IP Interfaces and creates corresponding OSPF Interfaces - The TOS 0 metrics are autonomously derived from ifSpeed - The OSPF Process automatically creates the Areas required for the Interfaces The simplest configuration of an OSPF process requires that: - The OSPF Process be Enabled. Baker & Coltun Standards Track [Page 8] RFC 1850 OSPF MIB November 1995 This can be accomplished with a single SET: ospfAdminStat := enabled. The configured system will have the following attributes: - The RouterID will be one of the IP addresses of the device - The device will be neither an Area Border Router nor an Autonomous System Border Router. - Every IP Interface, with or without an address, will be an OSPF Interface. - The AreaID of each interface will be 0.0.0.0, the Backbone. - Authentication will be disabled - All Broadcast and Point to Point interfaces will be operational. NBMA Interfaces require the configuration of at least one neighbor. - Timers on all direct interfaces will be: Hello Interval: 10 seconds Dead Timeout: 40 Seconds Retransmission: 5 Seconds Transit Delay: 1 Second Poll Interval: 120 Seconds - no direct links to hosts will be configured. - no addresses will be summarized - Metrics, being a measure of bit duration, are unambiguous and intelligent. - No Virtual Links will be configured. Baker & Coltun Standards Track [Page 9] RFC 1850 OSPF MIB November 1995 3. Definitions OSPF-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, Integer32, IpAddress FROM SNMPv2-SMI TEXTUAL-CONVENTION, TruthValue, RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF mib-2 FROM RFC1213-MIB; -- This MIB module uses the extended OBJECT-TYPE macro as -- defined in [9]. ospf MODULE-IDENTITY LAST-UPDATED "9501201225Z" -- Fri Jan 20 12:25:50 PST 1995 ORGANIZATION "IETF OSPF Working Group" CONTACT-INFO " Fred Baker Postal: Cisco Systems 519 Lado Drive Santa Barbara, California 93111 Tel: +1 805 681 0115 E-Mail: fred@cisco.com Rob Coltun Postal: RainbowBridge Communications Tel: (301) 340-9416 E-Mail: rcoltun@rainbow-bridge.com" DESCRIPTION "The MIB module to describe the OSPF Version 2 Protocol" ::= { mib-2 14 } -- The Area ID, in OSPF, has the same format as an IP Address, -- but has the function of defining a summarization point for -- Link State Advertisements AreaID ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An OSPF Area Identifier." SYNTAX IpAddress -- The Router ID, in OSPF, has the same format as an IP Address, Baker & Coltun Standards Track [Page 10] RFC 1850 OSPF MIB November 1995 -- but identifies the router independent of its IP Address. RouterID ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A OSPF Router Identifier." SYNTAX IpAddress -- The OSPF Metric is defined as an unsigned value in the range Metric ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The OSPF Internal Metric." SYNTAX Integer32 (0..'FFFF'h) BigMetric ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The OSPF External Metric." SYNTAX Integer32 (0..'FFFFFF'h) -- Status Values Status ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The status of an interface: 'enabled' indicates that it is willing to communicate with other OSPF Routers, while 'disabled' indicates that it is not." SYNTAX INTEGER { enabled (1), disabled (2) } -- Time Durations measured in seconds PositiveInteger ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A positive integer. Values in excess are precluded as unnecessary and prone to interoperability issues." SYNTAX Integer32 (0..'7FFFFFFF'h) HelloRange ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The range of intervals on which hello messages are exchanged." SYNTAX Integer32 (1..'FFFF'h) Baker & Coltun Standards Track [Page 11] RFC 1850 OSPF MIB November 1995 UpToMaxAge ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The values that one might find or configure for variables bounded by the maximum age of an LSA." SYNTAX Integer32 (0..3600) -- The range of ifIndex InterfaceIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The range of ifIndex." SYNTAX Integer32 -- Potential Priorities for the Designated Router Election DesignatedRouterPriority ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The values defined for the priority of a system for becoming the designated router." SYNTAX Integer32 (0..'FF'h) TOSType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Type of Service is defined as a mapping to the IP Type of Service Flags as defined in the IP Forwarding Table MIB +-----+-----+-----+-----+-----+-----+-----+-----+ | | | | | PRECEDENCE | TYPE OF SERVICE | 0 | | | | | +-----+-----+-----+-----+-----+-----+-----+-----+ IP TOS IP TOS Field Policy Field Policy Contents Code Contents Code 0 0 0 0 ==> 0 0 0 0 1 ==> 2 0 0 1 0 ==> 4 0 0 1 1 ==> 6 0 1 0 0 ==> 8 0 1 0 1 ==> 10 0 1 1 0 ==> 12 0 1 1 1 ==> 14 1 0 0 0 ==> 16 1 0 0 1 ==> 18 1 0 1 0 ==> 20 1 0 1 1 ==> 22 Baker & Coltun Standards Track [Page 12] RFC 1850 OSPF MIB November 1995 1 1 0 0 ==> 24 1 1 0 1 ==> 26 1 1 1 0 ==> 28 1 1 1 1 ==> 30 The remaining values are left for future definition." SYNTAX Integer32 (0..30) -- OSPF General Variables -- These parameters apply globally to the Router's -- OSPF Process. ospfGeneralGroup OBJECT IDENTIFIER ::= { ospf 1 } ospfRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-write STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the router in the Autonomous System. By convention, to ensure uniqueness, this should default to the value of one of the router's IP interface addresses." REFERENCE "OSPF Version 2, C.1 Global parameters" ::= { ospfGeneralGroup 1 } ospfAdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-write STATUS current DESCRIPTION "The administrative status of OSPF in the router. The value 'enabled' denotes that the OSPF Process is active on at least one inter- face; 'disabled' disables it on all inter- faces." ::= { ospfGeneralGroup 2 } ospfVersionNumber OBJECT-TYPE SYNTAX INTEGER { version2 (2) } MAX-ACCESS read-only STATUS current DESCRIPTION Baker & Coltun Standards Track [Page 13] RFC 1850 OSPF MIB November 1995 "The current version number of the OSPF proto- col is 2." REFERENCE "OSPF Version 2, Title" ::= { ospfGeneralGroup 3 } ospfAreaBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A flag to note whether this router is an area border router." REFERENCE "OSPF Version 2, Section 3 Splitting the AS into Areas" ::= { ospfGeneralGroup 4 } ospfASBdrRtrStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "A flag to note whether this router is config- ured as an Autonomous System border router." REFERENCE "OSPF Version 2, Section 3.3 Classification of routers" ::= { ospfGeneralGroup 5 } ospfExternLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of external (LS type 5) link-state advertisements in the link-state database." REFERENCE "OSPF Version 2, Appendix A.4.5 AS external link advertisements" ::= { ospfGeneralGroup 6 } ospfExternLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only Baker & Coltun Standards Track [Page 14] RFC 1850 OSPF MIB November 1995 STATUS current DESCRIPTION "The 32-bit unsigned sum of the LS checksums of the external link-state advertisements con- tained in the link-state database. This sum can be used to determine if there has been a change in a router's link state database, and to compare the link-state database of two routers." ::= { ospfGeneralGroup 7 } ospfTOSSupport OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The router's support for type-of-service rout- ing." REFERENCE "OSPF Version 2, Appendix F.1.2 Optional TOS support" ::= { ospfGeneralGroup 8 } ospfOriginateNewLsas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of new link-state advertisements that have been originated. This number is in- cremented each time the router originates a new LSA." ::= { ospfGeneralGroup 9 } ospfRxNewLsas OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of link-state advertisements re- ceived determined to be new instantiations. This number does not include newer instantia- tions of self-originated link-state advertise- ments." ::= { ospfGeneralGroup 10 } Baker & Coltun Standards Track [Page 15] RFC 1850 OSPF MIB November 1995 ospfExtLsdbLimit OBJECT-TYPE SYNTAX Integer32 (-1..'7FFFFFFF'h) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of non-default AS- external-LSAs entries that can be stored in the link-state database. If the value is -1, then there is no limit. When the number of non-default AS-external-LSAs in a router's link-state database reaches ospfExtLsdbLimit, the router enters Overflow- State. The router never holds more than ospfExtLsdbLimit non-default AS-external-LSAs in its database. OspfExtLsdbLimit MUST be set identically in all routers attached to the OSPF backbone and/or any regular OSPF area. (i.e., OSPF stub areas and NSSAs are excluded)." DEFVAL { -1 } ::= { ospfGeneralGroup 11 } ospfMulticastExtensions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "A Bit Mask indicating whether the router is forwarding IP multicast (Class D) datagrams based on the algorithms defined in the Multi- cast Extensions to OSPF. Bit 0, if set, indicates that the router can forward IP multicast datagrams in the router's directly attached areas (called intra-area mul- ticast routing). Bit 1, if set, indicates that the router can forward IP multicast datagrams between OSPF areas (called inter-area multicast routing). Bit 2, if set, indicates that the router can forward IP multicast datagrams between Auto- nomous Systems (called inter-AS multicast rout- ing). Only certain combinations of bit settings are allowed, namely: 0 (no multicast forwarding is Baker & Coltun Standards Track [Page 16] RFC 1850 OSPF MIB November 1995 enabled), 1 (intra-area multicasting only), 3 (intra-area and inter-area multicasting), 5 (intra-area and inter-AS multicasting) and 7 (multicasting everywhere). By default, no mul- ticast forwarding is enabled." DEFVAL { 0 } ::= { ospfGeneralGroup 12 } ospfExitOverflowInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds that, after entering OverflowState, a router will attempt to leave OverflowState. This allows the router to again originate non-default AS-external-LSAs. When set to 0, the router will not leave Overflow- State until restarted." DEFVAL { 0 } ::= { ospfGeneralGroup 13 } ospfDemandExtensions OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The router's support for demand routing." REFERENCE "OSPF Version 2, Appendix on Demand Routing" ::= { ospfGeneralGroup 14 } -- The OSPF Area Data Structure contains information -- regarding the various areas. The interfaces and -- virtual links are configured as part of these areas. -- Area 0.0.0.0, by definition, is the Backbone Area ospfAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the configured parame- ters and cumulative statistics of the router's attached areas." Baker & Coltun Standards Track [Page 17] RFC 1850 OSPF MIB November 1995 REFERENCE "OSPF Version 2, Section 6 The Area Data Struc- ture" ::= { ospf 2 } ospfAreaEntry OBJECT-TYPE SYNTAX OspfAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information describing the configured parame- ters and cumulative statistics of one of the router's attached areas." INDEX { ospfAreaId } ::= { ospfAreaTable 1 } OspfAreaEntry ::= SEQUENCE { ospfAreaId AreaID, ospfAuthType Integer32, ospfImportAsExtern INTEGER, ospfSpfRuns Counter32, ospfAreaBdrRtrCount Gauge32, ospfAsBdrRtrCount Gauge32, ospfAreaLsaCount Gauge32, ospfAreaLsaCksumSum Integer32, ospfAreaSummary INTEGER, ospfAreaStatus RowStatus } ospfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone." Baker & Coltun Standards Track [Page 18] RFC 1850 OSPF MIB November 1995 REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfAreaEntry 1 } ospfAuthType OBJECT-TYPE SYNTAX Integer32 -- none (0), -- simplePassword (1) -- md5 (2) -- reserved for specification by IANA (> 2) MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The authentication type specified for an area. Additional authentication types may be assigned locally on a per Area basis." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { ospfAreaEntry 2 } ospfImportAsExtern OBJECT-TYPE SYNTAX INTEGER { importExternal (1), importNoExternal (2), importNssa (3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The area's support for importing AS external link- state advertisements." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" DEFVAL { importExternal } ::= { ospfAreaEntry 3 } ospfSpfRuns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that the intra-area route table has been calculated using this area's link-state database. This is typically done using Dijkstra's algorithm." Baker & Coltun Standards Track [Page 19] RFC 1850 OSPF MIB November 1995 ::= { ospfAreaEntry 4 } ospfAreaBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of area border routers reach- able within this area. This is initially zero, and is calculated in each SPF Pass." ::= { ospfAreaEntry 5 } ospfAsBdrRtrCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of Autonomous System border routers reachable within this area. This is initially zero, and is calculated in each SPF Pass." ::= { ospfAreaEntry 6 } ospfAreaLsaCount OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of link-state advertisements in this area's link-state database, excluding AS External LSA's." ::= { ospfAreaEntry 7 } ospfAreaLsaCksumSum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The 32-bit unsigned sum of the link-state ad- vertisements' LS checksums contained in this area's link-state database. This sum excludes external (LS type 5) link-state advertisements. The sum can be used to determine if there has been a change in a router's link state data- base, and to compare the link-state database of Baker & Coltun Standards Track [Page 20] RFC 1850 OSPF MIB November 1995 two routers." DEFVAL { 0 } ::= { ospfAreaEntry 8 } ospfAreaSummary OBJECT-TYPE SYNTAX INTEGER { noAreaSummary (1), sendAreaSummary (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The variable ospfAreaSummary controls the im- port of summary LSAs into stub areas. It has no effect on other areas. If it is noAreaSummary, the router will neither originate nor propagate summary LSAs into the stub area. It will rely entirely on its de- fault route. If it is sendAreaSummary, the router will both summarize and propagate summary LSAs." DEFVAL { noAreaSummary } ::= { ospfAreaEntry 9 } ospfAreaStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfAreaEntry 10 } -- OSPF Area Default Metric Table -- The OSPF Area Default Metric Table describes the metrics -- that a default Area Border Router will advertise into a -- Stub area. ospfStubAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfStubAreaEntry Baker & Coltun Standards Track [Page 21] RFC 1850 OSPF MIB November 1995 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The set of metrics that will be advertised by a default Area Border Router into a stub area." REFERENCE "OSPF Version 2, Appendix C.2, Area Parameters" ::= { ospf 3 } ospfStubAreaEntry OBJECT-TYPE SYNTAX OspfStubAreaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The metric for a given Type of Service that will be advertised by a default Area Border Router into a stub area." REFERENCE "OSPF Version 2, Appendix C.2, Area Parameters" INDEX { ospfStubAreaId, ospfStubTOS } ::= { ospfStubAreaTable 1 } OspfStubAreaEntry ::= SEQUENCE { ospfStubAreaId AreaID, ospfStubTOS TOSType, ospfStubMetric BigMetric, ospfStubStatus RowStatus, ospfStubMetricType INTEGER } ospfStubAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit identifier for the Stub Area. On creation, this can be derived from the in- stance." ::= { ospfStubAreaEntry 1 } Baker & Coltun Standards Track [Page 22] RFC 1850 OSPF MIB November 1995 ospfStubTOS OBJECT-TYPE SYNTAX TOSType MAX-ACCESS read-only STATUS current DESCRIPTION "The Type of Service associated with the metric. On creation, this can be derived from the instance." ::= { ospfStubAreaEntry 2 } ospfStubMetric OBJECT-TYPE SYNTAX BigMetric MAX-ACCESS read-create STATUS current DESCRIPTION "The metric value applied at the indicated type of service. By default, this equals the least metric at the type of service among the inter- faces to other areas." ::= { ospfStubAreaEntry 3 } ospfStubStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfStubAreaEntry 4 } ospfStubMetricType OBJECT-TYPE SYNTAX INTEGER { ospfMetric (1), -- OSPF Metric comparableCost (2), -- external type 1 nonComparable (3) -- external type 2 } MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the type of metric ad- vertised as a default route." DEFVAL { ospfMetric } ::= { ospfStubAreaEntry 5 } Baker & Coltun Standards Track [Page 23] RFC 1850 OSPF MIB November 1995 -- OSPF Link State Database -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. ospfLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's Link State Database." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { ospf 4 } ospfLsdbEntry OBJECT-TYPE SYNTAX OspfLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link State Advertisement." INDEX { ospfLsdbAreaId, ospfLsdbType, ospfLsdbLsid, ospfLsdbRouterId } ::= { ospfLsdbTable 1 } OspfLsdbEntry ::= SEQUENCE { ospfLsdbAreaId AreaID, ospfLsdbType INTEGER, ospfLsdbLsid IpAddress, ospfLsdbRouterId RouterID, ospfLsdbSequence Integer32, ospfLsdbAge Integer32, ospfLsdbChecksum Integer32, ospfLsdbAdvertisement OCTET STRING } Baker & Coltun Standards Track [Page 24] RFC 1850 OSPF MIB November 1995 ospfLsdbAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit identifier of the Area from which the LSA was received." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfLsdbEntry 1 } -- External Link State Advertisements are permitted -- for backward compatibility, but should be displayed in -- the ospfExtLsdbTable rather than here. ospfLsdbType OBJECT-TYPE SYNTAX INTEGER { routerLink (1), networkLink (2), summaryLink (3), asSummaryLink (4), asExternalLink (5), -- but see ospfExtLsdbTable multicastLink (6), nssaExternalLink (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { ospfLsdbEntry 2 } ospfLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." REFERENCE "OSPF Version 2, Section 12.1.4 Link State ID" ::= { ospfLsdbEntry 3 } Baker & Coltun Standards Track [Page 25] RFC 1850 OSPF MIB November 1995 ospfLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { ospfLsdbEntry 4 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. ospfLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { ospfLsdbEntry 5 } ospfLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { ospfLsdbEntry 6 } ospfLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current Baker & Coltun Standards Track [Page 26] RFC 1850 OSPF MIB November 1995 DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { ospfLsdbEntry 7 } ospfLsdbAdvertisement OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { ospfLsdbEntry 8 } -- Address Range Table -- The Address Range Table acts as an adjunct to the Area -- Table; It describes those Address Range Summaries that -- are configured to be propagated from an Area to reduce -- the amount of information about it which is known beyond -- its borders. ospfAreaRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfAreaRangeEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255" REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospf 5 } Baker & Coltun Standards Track [Page 27] RFC 1850 OSPF MIB November 1995 ospfAreaRangeEntry OBJECT-TYPE SYNTAX OspfAreaRangeEntry MAX-ACCESS not-accessible STATUS obsolete DESCRIPTION "A range if IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255" REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" INDEX { ospfAreaRangeAreaId, ospfAreaRangeNet } ::= { ospfAreaRangeTable 1 } OspfAreaRangeEntry ::= SEQUENCE { ospfAreaRangeAreaId AreaID, ospfAreaRangeNet IpAddress, ospfAreaRangeMask IpAddress, ospfAreaRangeStatus RowStatus, ospfAreaRangeEffect INTEGER } ospfAreaRangeAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The Area the Address Range is to be found within." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfAreaRangeEntry 1 } ospfAreaRangeNet OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS obsolete DESCRIPTION "The IP Address of the Net or Subnet indicated by the range." Baker & Coltun Standards Track [Page 28] RFC 1850 OSPF MIB November 1995 REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfAreaRangeEntry 2 } ospfAreaRangeMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS obsolete DESCRIPTION "The Subnet Mask that pertains to the Net or Subnet." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfAreaRangeEntry 3 } ospfAreaRangeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS obsolete DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfAreaRangeEntry 4 } ospfAreaRangeEffect OBJECT-TYPE SYNTAX INTEGER { advertiseMatching (1), doNotAdvertiseMatching (2) } MAX-ACCESS read-create STATUS obsolete DESCRIPTION "Subnets subsumed by ranges either trigger the advertisement of the indicated summary (adver- tiseMatching), or result in the subnet's not being advertised at all outside the area." DEFVAL { advertiseMatching } ::= { ospfAreaRangeEntry 5 } -- OSPF Host Table -- The Host/Metric Table indicates what hosts are directly Baker & Coltun Standards Track [Page 29] RFC 1850 OSPF MIB November 1995 -- attached to the Router, and what metrics and types of -- service should be advertised for them. ospfHostTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The list of Hosts, and their metrics, that the router will advertise as host routes." REFERENCE "OSPF Version 2, Appendix C.6 Host route param- eters" ::= { ospf 6 } ospfHostEntry OBJECT-TYPE SYNTAX OspfHostEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A metric to be advertised, for a given type of service, when a given host is reachable." INDEX { ospfHostIpAddress, ospfHostTOS } ::= { ospfHostTable 1 } OspfHostEntry ::= SEQUENCE { ospfHostIpAddress IpAddress, ospfHostTOS TOSType, ospfHostMetric Metric, ospfHostStatus RowStatus, ospfHostAreaID AreaID } ospfHostIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the Host." REFERENCE "OSPF Version 2, Appendix C.6 Host route parame- Baker & Coltun Standards Track [Page 30] RFC 1850 OSPF MIB November 1995 ters" ::= { ospfHostEntry 1 } ospfHostTOS OBJECT-TYPE SYNTAX TOSType MAX-ACCESS read-only STATUS current DESCRIPTION "The Type of Service of the route being config- ured." REFERENCE "OSPF Version 2, Appendix C.6 Host route parame- ters" ::= { ospfHostEntry 2 } ospfHostMetric OBJECT-TYPE SYNTAX Metric MAX-ACCESS read-create STATUS current DESCRIPTION "The Metric to be advertised." REFERENCE "OSPF Version 2, Appendix C.6 Host route parame- ters" ::= { ospfHostEntry 3 } ospfHostStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfHostEntry 4 } ospfHostAreaID OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF in- terface is in, or 0.0.0.0" Baker & Coltun Standards Track [Page 31] RFC 1850 OSPF MIB November 1995 REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfHostEntry 5 } -- OSPF Interface Table -- The OSPF Interface Table augments the ipAddrTable -- with OSPF specific information. ospfIfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF." REFERENCE "OSPF Version 2, Appendix C.3 Router interface parameters" ::= { ospf 7 } ospfIfEntry OBJECT-TYPE SYNTAX OspfIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF." INDEX { ospfIfIpAddress, ospfAddressLessIf } ::= { ospfIfTable 1 } OspfIfEntry ::= SEQUENCE { ospfIfIpAddress IpAddress, ospfAddressLessIf Integer32, ospfIfAreaId AreaID, ospfIfType INTEGER, ospfIfAdminStat Status, ospfIfRtrPriority DesignatedRouterPriority, ospfIfTransitDelay Baker & Coltun Standards Track [Page 32] RFC 1850 OSPF MIB November 1995 UpToMaxAge, ospfIfRetransInterval UpToMaxAge, ospfIfHelloInterval HelloRange, ospfIfRtrDeadInterval PositiveInteger, ospfIfPollInterval PositiveInteger, ospfIfState INTEGER, ospfIfDesignatedRouter IpAddress, ospfIfBackupDesignatedRouter IpAddress, ospfIfEvents Counter32, ospfIfAuthType INTEGER, ospfIfAuthKey OCTET STRING, ospfIfStatus RowStatus, ospfIfMulticastForwarding INTEGER, ospfIfDemand TruthValue } ospfIfIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of this OSPF interface." ::= { ospfIfEntry 1 } ospfAddressLessIf OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces having no IP Address." ::= { ospfIfEntry 2 } Baker & Coltun Standards Track [Page 33] RFC 1850 OSPF MIB November 1995 ospfIfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-create STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { ospfIfEntry 3 } ospfIfType OBJECT-TYPE SYNTAX INTEGER { broadcast (1), nbma (2), pointToPoint (3), pointToMultipoint (5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25 and similar technologies take the value 'nbma', and links that are definitively point to point take the value 'pointToPoint'." ::= { ospfIfEntry 4 } ospfIfAdminStat OBJECT-TYPE SYNTAX Status MAX-ACCESS read-create STATUS current DESCRIPTION "The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to OSPF." DEFVAL { enabled } ::= { ospfIfEntry 5 } ospfIfRtrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority Baker & Coltun Standards Track [Page 34] RFC 1850 OSPF MIB November 1995 MAX-ACCESS read-create STATUS current DESCRIPTION "The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designated router on this particular network. In the event of a tie in this value, routers will use their Router ID as a tie breaker." DEFVAL { 1 } ::= { ospfIfEntry 6 } ospfIfTransitDelay OBJECT-TYPE SYNTAX UpToMaxAge MAX-ACCESS read-create STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link state update packet over this interface." DEFVAL { 1 } ::= { ospfIfEntry 7 } ospfIfRetransInterval OBJECT-TYPE SYNTAX UpToMaxAge MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets." DEFVAL { 5 } ::= { ospfIfEntry 8 } ospfIfHelloInterval OBJECT-TYPE SYNTAX HelloRange MAX-ACCESS read-create STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- Baker & Coltun Standards Track [Page 35] RFC 1850 OSPF MIB November 1995 terface. This value must be the same for all routers attached to a common network." DEFVAL { 10 } ::= { ospfIfEntry 9 } ospfIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for all routers attached to a common network." DEFVAL { 40 } ::= { ospfIfEntry 10 } ospfIfPollInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor." DEFVAL { 120 } ::= { ospfIfEntry 11 } ospfIfState OBJECT-TYPE SYNTAX INTEGER { down (1), loopback (2), waiting (3), pointToPoint (4), designatedRouter (5), backupDesignatedRouter (6), otherDesignatedRouter (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The OSPF Interface State." DEFVAL { down } Baker & Coltun Standards Track [Page 36] RFC 1850 OSPF MIB November 1995 ::= { ospfIfEntry 12 } ospfIfDesignatedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { ospfIfEntry 13 } ospfIfBackupDesignatedRouter OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the Backup Designated Router." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { ospfIfEntry 14 } ospfIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this OSPF interface has changed its state, or an error has occurred." ::= { ospfIfEntry 15 } ospfIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- Baker & Coltun Standards Track [Page 37] RFC 1850 OSPF MIB November 1995 ment. When read, ospfIfAuthKey always returns an Oc- tet String of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 ::= { ospfIfEntry 16 } ospfIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfIfEntry 17 } ospfIfMulticastForwarding OBJECT-TYPE SYNTAX INTEGER { blocked (1), -- no multicast forwarding multicast (2), -- using multicast address unicast (3) -- to each OSPF neighbor } MAX-ACCESS read-create STATUS current DESCRIPTION "The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NBMA interfaces, and setting ospfMulticastForwarding to 0 effective- ly disables all multicast forwarding." DEFVAL { blocked } ::= { ospfIfEntry 18 } ospfIfDemand OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether Demand OSPF procedures (hel- Baker & Coltun Standards Track [Page 38] RFC 1850 OSPF MIB November 1995 lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface." DEFVAL { false } ::= { ospfIfEntry 19 } ospfIfAuthType OBJECT-TYPE SYNTAX INTEGER (0..255) -- none (0), -- simplePassword (1) -- md5 (2) -- reserved for specification by IANA (> 2) MAX-ACCESS read-create STATUS current DESCRIPTION "The authentication type specified for an in- terface. Additional authentication types may be assigned locally." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { ospfIfEntry 20 } -- OSPF Interface Metric Table -- The Metric Table describes the metrics to be advertised -- for a specified interface at the various types of service. -- As such, this table is an adjunct of the OSPF Interface -- Table. -- Types of service, as defined by RFC 791, have the ability -- to request low delay, high bandwidth, or reliable linkage. -- For the purposes of this specification, the measure of -- bandwidth -- Metric = 10^8 / ifSpeed -- is the default value. For multiple link interfaces, note -- that ifSpeed is the sum of the individual link speeds. -- This yields a number having the following typical values: -- Network Type/bit rate Metric -- >= 100 MBPS 1 -- Ethernet/802.3 10 Baker & Coltun Standards Track [Page 39] RFC 1850 OSPF MIB November 1995 -- E1 48 -- T1 (ESF) 65 -- 64 KBPS 1562 -- 56 KBPS 1785 -- 19.2 KBPS 5208 -- 9.6 KBPS 10416 -- Routes that are not specified use the default (TOS 0) metric ospfIfMetricTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfIfMetricEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The TOS metrics for a non-virtual interface identified by the interface index." REFERENCE "OSPF Version 2, Appendix C.3 Router interface parameters" ::= { ospf 8 } ospfIfMetricEntry OBJECT-TYPE SYNTAX OspfIfMetricEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A particular TOS metric for a non-virtual in- terface identified by the interface index." REFERENCE "OSPF Version 2, Appendix C.3 Router interface parameters" INDEX { ospfIfMetricIpAddress, ospfIfMetricAddressLessIf, ospfIfMetricTOS } ::= { ospfIfMetricTable 1 } OspfIfMetricEntry ::= SEQUENCE { ospfIfMetricIpAddress IpAddress, ospfIfMetricAddressLessIf Integer32, ospfIfMetricTOS TOSType, ospfIfMetricValue Metric, ospfIfMetricStatus RowStatus Baker & Coltun Standards Track [Page 40] RFC 1850 OSPF MIB November 1995 } ospfIfMetricIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of this OSPF interface. On row creation, this can be derived from the in- stance." ::= { ospfIfMetricEntry 1 } ospfIfMetricAddressLessIf OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the value of ifIndex for in- terfaces having no IP Address. On row crea- tion, this can be derived from the instance." ::= { ospfIfMetricEntry 2 } ospfIfMetricTOS OBJECT-TYPE SYNTAX TOSType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of service metric being referenced. On row creation, this can be derived from the instance." ::= { ospfIfMetricEntry 3 } ospfIfMetricValue OBJECT-TYPE SYNTAX Metric MAX-ACCESS read-create STATUS current DESCRIPTION "The metric of using this type of service on this interface. The default value of the TOS 0 Metric is 10^8 / ifSpeed." ::= { ospfIfMetricEntry 4 } ospfIfMetricStatus OBJECT-TYPE Baker & Coltun Standards Track [Page 41] RFC 1850 OSPF MIB November 1995 SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfIfMetricEntry 5 } -- OSPF Virtual Interface Table -- The Virtual Interface Table describes the virtual -- links that the OSPF Process is configured to -- carry on. ospfVirtIfTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfVirtIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about this router's virtual inter- faces." REFERENCE "OSPF Version 2, Appendix C.4 Virtual link parameters" ::= { ospf 9 } ospfVirtIfEntry OBJECT-TYPE SYNTAX OspfVirtIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single Virtual Interface." INDEX { ospfVirtIfAreaId, ospfVirtIfNeighbor } ::= { ospfVirtIfTable 1 } OspfVirtIfEntry ::= SEQUENCE { ospfVirtIfAreaId AreaID, ospfVirtIfNeighbor RouterID, ospfVirtIfTransitDelay UpToMaxAge, ospfVirtIfRetransInterval Baker & Coltun Standards Track [Page 42] RFC 1850 OSPF MIB November 1995 UpToMaxAge, ospfVirtIfHelloInterval HelloRange, ospfVirtIfRtrDeadInterval PositiveInteger, ospfVirtIfState INTEGER, ospfVirtIfEvents Counter32, ospfVirtIfAuthType INTEGER, ospfVirtIfAuthKey OCTET STRING, ospfVirtIfStatus RowStatus } ospfVirtIfAreaId OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0" ::= { ospfVirtIfEntry 1 } ospfVirtIfNeighbor OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The Router ID of the Virtual Neighbor." ::= { ospfVirtIfEntry 2 } ospfVirtIfTransitDelay OBJECT-TYPE SYNTAX UpToMaxAge MAX-ACCESS read-create STATUS current DESCRIPTION "The estimated number of seconds it takes to transmit a link- state update packet over this interface." DEFVAL { 1 } ::= { ospfVirtIfEntry 3 } Baker & Coltun Standards Track [Page 43] RFC 1850 OSPF MIB November 1995 ospfVirtIfRetransInterval OBJECT-TYPE SYNTAX UpToMaxAge MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request packets. This value should be well over the expected round- trip time." DEFVAL { 5 } ::= { ospfVirtIfEntry 4 } ospfVirtIfHelloInterval OBJECT-TYPE SYNTAX HelloRange MAX-ACCESS read-create STATUS current DESCRIPTION "The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor." DEFVAL { 10 } ::= { ospfVirtIfEntry 5 } ospfVirtIfRtrDeadInterval OBJECT-TYPE SYNTAX PositiveInteger MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for the virtual neigh- bor." DEFVAL { 60 } ::= { ospfVirtIfEntry 6 } ospfVirtIfState OBJECT-TYPE SYNTAX INTEGER { down (1), -- these use the same encoding pointToPoint (4) -- as the ospfIfTable Baker & Coltun Standards Track [Page 44] RFC 1850 OSPF MIB November 1995 } MAX-ACCESS read-only STATUS current DESCRIPTION "OSPF virtual interface states." DEFVAL { down } ::= { ospfVirtIfEntry 7 } ospfVirtIfEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of state changes or error events on this Virtual Link" ::= { ospfVirtIfEntry 8 } ospfVirtIfAuthKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- tication cannot use a key of more than 8 oc- tets. Larger keys are useful only with authen- tication mechanisms not specified in this docu- ment. When read, ospfVifAuthKey always returns a string of length zero." REFERENCE "OSPF Version 2, Section 9 The Interface Data Structure" DEFVAL { '0000000000000000'H } -- 0.0.0.0.0.0.0.0 ::= { ospfVirtIfEntry 9 } ospfVirtIfStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current Baker & Coltun Standards Track [Page 45] RFC 1850 OSPF MIB November 1995 DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfVirtIfEntry 10 } ospfVirtIfAuthType OBJECT-TYPE SYNTAX INTEGER (0..255) -- none (0), -- simplePassword (1) -- md5 (2) -- reserved for specification by IANA (> 2) MAX-ACCESS read-create STATUS current DESCRIPTION "The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally." REFERENCE "OSPF Version 2, Appendix E Authentication" DEFVAL { 0 } -- no authentication, by default ::= { ospfVirtIfEntry 11 } -- OSPF Neighbor Table -- The OSPF Neighbor Table describes all neighbors in -- the locality of the subject router. ospfNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of non-virtual neighbor information." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" ::= { ospf 10 } ospfNbrEntry OBJECT-TYPE SYNTAX OspfNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION Baker & Coltun Standards Track [Page 46] RFC 1850 OSPF MIB November 1995 "The information regarding a single neighbor." REFERENCE "OSPF Version 2, Section 10 The Neighbor Data Structure" INDEX { ospfNbrIpAddr, ospfNbrAddressLessIndex } ::= { ospfNbrTable 1 } OspfNbrEntry ::= SEQUENCE { ospfNbrIpAddr IpAddress, ospfNbrAddressLessIndex InterfaceIndex, ospfNbrRtrId RouterID, ospfNbrOptions Integer32, ospfNbrPriority DesignatedRouterPriority, ospfNbrState INTEGER, ospfNbrEvents Counter32, ospfNbrLsRetransQLen Gauge32, ospfNbmaNbrStatus RowStatus, ospfNbmaNbrPermanence INTEGER, ospfNbrHelloSuppressed TruthValue } ospfNbrIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address this neighbor is using in its IP Source Address. Note that, on addressless links, this will not be 0.0.0.0, but the ad- dress of another of the neighbor's interfaces." ::= { ospfNbrEntry 1 } ospfNbrAddressLessIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only Baker & Coltun Standards Track [Page 47] RFC 1850 OSPF MIB November 1995 STATUS current DESCRIPTION "On an interface having an IP Address, zero. On addressless interfaces, the corresponding value of ifIndex in the Internet Standard MIB. On row creation, this can be derived from the instance." ::= { ospfNbrEntry 2 } ospfNbrRtrId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer (represented as a type IpAd- dress) uniquely identifying the neighboring router in the Autonomous System." DEFVAL { '00000000'H } -- 0.0.0.0 ::= { ospfNbrEntry 3 } ospfNbrOptions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field. Bit 0, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 1, if set, indicates that the associated area accepts and operates on external informa- tion; if zero, it is a stub area. Bit 2, if set, indicates that the system is ca- pable of routing IP Multicast datagrams; i.e., that it implements the Multicast Extensions to OSPF. Bit 3, if set, indicates that the associated area is an NSSA. These areas are capable of carrying type 7 external advertisements, which are translated into type 5 external advertise- Baker & Coltun Standards Track [Page 48] RFC 1850 OSPF MIB November 1995 ments at NSSA borders." REFERENCE "OSPF Version 2, Section 12.1.2 Options" DEFVAL { 0 } ::= { ospfNbrEntry 4 } ospfNbrPriority OBJECT-TYPE SYNTAX DesignatedRouterPriority MAX-ACCESS read-create STATUS current DESCRIPTION "The priority of this neighbor in the designat- ed router election algorithm. The value 0 sig- nifies that the neighbor is not eligible to be- come the designated router on this particular network." DEFVAL { 1 } ::= { ospfNbrEntry 5 } ospfNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The State of the relationship with this Neigh- bor." REFERENCE "OSPF Version 2, Section 10.1 Neighbor States" DEFVAL { down } ::= { ospfNbrEntry 6 } ospfNbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Baker & Coltun Standards Track [Page 49] RFC 1850 OSPF MIB November 1995 "The number of times this neighbor relationship has changed state, or an error has occurred." ::= { ospfNbrEntry 7 } ospfNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current length of the retransmission queue." ::= { ospfNbrEntry 8 } ospfNbmaNbrStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfNbrEntry 9 } ospfNbmaNbrPermanence OBJECT-TYPE SYNTAX INTEGER { dynamic (1), -- learned through protocol permanent (2) -- configured address } MAX-ACCESS read-only STATUS current DESCRIPTION "This variable displays the status of the en- try. 'dynamic' and 'permanent' refer to how the neighbor became known." DEFVAL { permanent } ::= { ospfNbrEntry 10 } ospfNbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Hellos are being suppressed Baker & Coltun Standards Track [Page 50] RFC 1850 OSPF MIB November 1995 to the neighbor" ::= { ospfNbrEntry 11 } -- OSPF Virtual Neighbor Table -- This table describes all virtual neighbors. -- Since Virtual Links are configured in the -- virtual interface table, this table is read-only. ospfVirtNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfVirtNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of virtual neighbor information." REFERENCE "OSPF Version 2, Section 15 Virtual Links" ::= { ospf 11 } ospfVirtNbrEntry OBJECT-TYPE SYNTAX OspfVirtNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Virtual neighbor information." INDEX { ospfVirtNbrArea, ospfVirtNbrRtrId } ::= { ospfVirtNbrTable 1 } OspfVirtNbrEntry ::= SEQUENCE { ospfVirtNbrArea AreaID, ospfVirtNbrRtrId RouterID, ospfVirtNbrIpAddr IpAddress, ospfVirtNbrOptions Integer32, ospfVirtNbrState INTEGER, ospfVirtNbrEvents Counter32, ospfVirtNbrLsRetransQLen Gauge32, ospfVirtNbrHelloSuppressed TruthValue Baker & Coltun Standards Track [Page 51] RFC 1850 OSPF MIB November 1995 } ospfVirtNbrArea OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Transit Area Identifier." ::= { ospfVirtNbrEntry 1 } ospfVirtNbrRtrId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "A 32-bit integer uniquely identifying the neighboring router in the Autonomous System." ::= { ospfVirtNbrEntry 2 } ospfVirtNbrIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address this Virtual Neighbor is us- ing." ::= { ospfVirtNbrEntry 3 } ospfVirtNbrOptions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "A Bit Mask corresponding to the neighbor's op- tions field. Bit 1, if set, indicates that the system will operate on Type of Service metrics other than TOS 0. If zero, the neighbor will ignore all metrics except the TOS 0 metric. Bit 2, if set, indicates that the system is Network Multicast capable; ie, that it imple- ments OSPF Multicast Routing." ::= { ospfVirtNbrEntry 4 } Baker & Coltun Standards Track [Page 52] RFC 1850 OSPF MIB November 1995 ospfVirtNbrState OBJECT-TYPE SYNTAX INTEGER { down (1), attempt (2), init (3), twoWay (4), exchangeStart (5), exchange (6), loading (7), full (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the Virtual Neighbor Relation- ship." ::= { ospfVirtNbrEntry 5 } ospfVirtNbrEvents OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this virtual link has changed its state, or an error has occurred." ::= { ospfVirtNbrEntry 6 } ospfVirtNbrLsRetransQLen OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current length of the retransmission queue." ::= { ospfVirtNbrEntry 7 } ospfVirtNbrHelloSuppressed OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether Hellos are being suppressed to the neighbor" ::= { ospfVirtNbrEntry 8 } Baker & Coltun Standards Track [Page 53] RFC 1850 OSPF MIB November 1995 -- OSPF Link State Database, External -- The Link State Database contains the Link State -- Advertisements from throughout the areas that the -- device is attached to. -- This table is identical to the OSPF LSDB Table in -- format, but contains only External Link State -- Advertisements. The purpose is to allow external -- LSAs to be displayed once for the router rather -- than once in each non-stub area. ospfExtLsdbTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfExtLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The OSPF Process's Links State Database." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { ospf 12 } ospfExtLsdbEntry OBJECT-TYPE SYNTAX OspfExtLsdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A single Link State Advertisement." INDEX { ospfExtLsdbType, ospfExtLsdbLsid, ospfExtLsdbRouterId } ::= { ospfExtLsdbTable 1 } OspfExtLsdbEntry ::= SEQUENCE { ospfExtLsdbType INTEGER, ospfExtLsdbLsid IpAddress, ospfExtLsdbRouterId RouterID, ospfExtLsdbSequence Integer32, ospfExtLsdbAge Integer32, ospfExtLsdbChecksum Integer32, ospfExtLsdbAdvertisement Baker & Coltun Standards Track [Page 54] RFC 1850 OSPF MIB November 1995 OCTET STRING } ospfExtLsdbType OBJECT-TYPE SYNTAX INTEGER { asExternalLink (5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the link state advertisement. Each link state type has a separate advertise- ment format." REFERENCE "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { ospfExtLsdbEntry 1 } ospfExtLsdbLsid OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement." REFERENCE "OSPF Version 2, Section 12.1.4 Link State ID" ::= { ospfExtLsdbEntry 2 } ospfExtLsdbRouterId OBJECT-TYPE SYNTAX RouterID MAX-ACCESS read-only STATUS current DESCRIPTION "The 32 bit number that uniquely identifies the originating router in the Autonomous System." REFERENCE "OSPF Version 2, Appendix C.1 Global parameters" ::= { ospfExtLsdbEntry 3 } -- Note that the OSPF Sequence Number is a 32 bit signed -- integer. It starts with the value '80000001'h, -- or -'7FFFFFFF'h, and increments until '7FFFFFFF'h -- Thus, a typical sequence number will be very negative. Baker & Coltun Standards Track [Page 55] RFC 1850 OSPF MIB November 1995 ospfExtLsdbSequence OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement." REFERENCE "OSPF Version 2, Section 12.1.6 LS sequence number" ::= { ospfExtLsdbEntry 4 } ospfExtLsdbAge OBJECT-TYPE SYNTAX Integer32 -- Should be 0..MaxAge MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the age of the link state adver- tisement in seconds." REFERENCE "OSPF Version 2, Section 12.1.1 LS age" ::= { ospfExtLsdbEntry 5 } ospfExtLsdbChecksum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum." REFERENCE "OSPF Version 2, Section 12.1.7 LS checksum" ::= { ospfExtLsdbEntry 6 } ospfExtLsdbAdvertisement OBJECT-TYPE Baker & Coltun Standards Track [Page 56] RFC 1850 OSPF MIB November 1995 SYNTAX OCTET STRING (SIZE(36)) MAX-ACCESS read-only STATUS current DESCRIPTION "The entire Link State Advertisement, including its header." REFERENCE "OSPF Version 2, Section 12 Link State Adver- tisements" ::= { ospfExtLsdbEntry 7 } -- OSPF Use of the CIDR Route Table ospfRouteGroup OBJECT IDENTIFIER ::= { ospf 13 } -- The IP Forwarding Table defines a number of objects for use by -- the routing protocol to externalize its information. Most of -- the variables (ipForwardDest, ipForwardMask, ipForwardPolicy, -- ipForwardNextHop, ipForwardIfIndex, ipForwardType, -- ipForwardProto, ipForwardAge, and ipForwardNextHopAS) are -- defined there. -- Those that leave some discretion are defined here. -- ipCidrRouteProto is, of course, ospf (13). -- ipCidrRouteAge is the time since the route was first calculated, -- as opposed to the time since the last SPF run. -- ipCidrRouteInfo is an OBJECT IDENTIFIER for use by the routing -- protocol. The following values shall be found there depending -- on the way the route was calculated. ospfIntraArea OBJECT IDENTIFIER ::= { ospfRouteGroup 1 } ospfInterArea OBJECT IDENTIFIER ::= { ospfRouteGroup 2 } ospfExternalType1 OBJECT IDENTIFIER ::= { ospfRouteGroup 3 } ospfExternalType2 OBJECT IDENTIFIER ::= { ospfRouteGroup 4 } -- ipCidrRouteMetric1 is, by definition, the primary routing -- metric. Therefore, it should be the metric that route -- selection is based on. For intra-area and inter-area routes, -- it is an OSPF metric. For External Type 1 (comparable value) -- routes, it is an OSPF metric plus the External Metric. For -- external Type 2 (non-comparable value) routes, it is the -- external metric. -- ipCidrRouteMetric2 is, by definition, a secondary routing Baker & Coltun Standards Track [Page 57] RFC 1850 OSPF MIB November 1995 -- metric. Therefore, it should be the metric that breaks a tie -- among routes having equal metric1 values and the same -- calculation rule. For intra-area, inter-area routes, and -- External Type 1 (comparable value) routes, it is unused. For -- external Type 2 (non-comparable value) routes, it is the metric -- to the AS border router. -- ipCidrRouteMetric3, ipCidrRouteMetric4, and ipCidrRouteMetric5 are -- unused. -- -- The OSPF Area Aggregate Table -- -- This table replaces the OSPF Area Summary Table, being an -- extension of that for CIDR routers. ospfAreaAggregateTable OBJECT-TYPE SYNTAX SEQUENCE OF OspfAreaAggregateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A range of IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are configured such that one range sub- sumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the most specific match is the preferred one." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospf 14 } ospfAreaAggregateEntry OBJECT-TYPE SYNTAX OspfAreaAggregateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A range of IP addresses specified by an IP address/IP network mask pair. For example, class B address range of X.X.X.X with a network mask of 255.255.0.0 includes all IP addresses from X.X.0.0 to X.X.255.255. Note that if ranges are range configured such that one range subsumes another range (e.g., 10.0.0.0 mask 255.0.0.0 and 10.1.0.0 mask 255.255.0.0), the Baker & Coltun Standards Track [Page 58] RFC 1850 OSPF MIB November 1995 most specific match is the preferred one." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" INDEX { ospfAreaAggregateAreaID, ospfAreaAggregateLsdbType, ospfAreaAggregateNet, ospfAreaAggregateMask } ::= { ospfAreaAggregateTable 1 } OspfAreaAggregateEntry ::= SEQUENCE { ospfAreaAggregateAreaID AreaID, ospfAreaAggregateLsdbType INTEGER, ospfAreaAggregateNet IpAddress, ospfAreaAggregateMask IpAddress, ospfAreaAggregateStatus RowStatus, ospfAreaAggregateEffect INTEGER } ospfAreaAggregateAreaID OBJECT-TYPE SYNTAX AreaID MAX-ACCESS read-only STATUS current DESCRIPTION "The Area the Address Aggregate is to be found within." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfAreaAggregateEntry 1 } ospfAreaAggregateLsdbType OBJECT-TYPE SYNTAX INTEGER { summaryLink (3), nssaExternalLink (7) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the Address Aggregate. This field specifies the Lsdb type that this Address Ag- gregate applies to." REFERENCE Baker & Coltun Standards Track [Page 59] RFC 1850 OSPF MIB November 1995 "OSPF Version 2, Appendix A.4.1 The Link State Advertisement header" ::= { ospfAreaAggregateEntry 2 } ospfAreaAggregateNet OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the Net or Subnet indicated by the range." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfAreaAggregateEntry 3 } ospfAreaAggregateMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Subnet Mask that pertains to the Net or Subnet." REFERENCE "OSPF Version 2, Appendix C.2 Area parameters" ::= { ospfAreaAggregateEntry 4 } ospfAreaAggregateStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent." ::= { ospfAreaAggregateEntry 5 } ospfAreaAggregateEffect OBJECT-TYPE SYNTAX INTEGER { advertiseMatching (1), doNotAdvertiseMatching (2) } MAX-ACCESS read-create STATUS current Baker & Coltun Standards Track [Page 60] RFC 1850 OSPF MIB November 1995 DESCRIPTION "Subnets subsumed by ranges either trigger the advertisement of the indicated aggregate (ad- vertiseMatching), or result in the subnet's not being advertised at all outside the area." DEFVAL { advertiseMatching } ::= { ospfAreaAggregateEntry 6 } -- conformance information ospfConformance OBJECT IDENTIFIER ::= { ospf 15 } ospfGroups OBJECT IDENTIFIER ::= { ospfConformance 1 } ospfCompliances OBJECT IDENTIFIER ::= { ospfConformance 2 } -- compliance statements ospfCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement " MODULE -- this module MANDATORY-GROUPS { ospfBasicGroup, ospfAreaGroup, ospfStubAreaGroup, ospfIfGroup, ospfIfMetricGroup, ospfVirtIfGroup, ospfNbrGroup, ospfVirtNbrGroup, ospfAreaAggregateGroup } ::= { ospfCompliances 1 } -- units of conformance ospfBasicGroup OBJECT-GROUP OBJECTS { ospfRouterId, ospfAdminStat, ospfVersionNumber, ospfAreaBdrRtrStatus, ospfASBdrRtrStatus, ospfExternLsaCount, ospfExternLsaCksumSum, Baker & Coltun Standards Track [Page 61] RFC 1850 OSPF MIB November 1995 ospfTOSSupport, ospfOriginateNewLsas, ospfRxNewLsas, ospfExtLsdbLimit, ospfMulticastExtensions, ospfExitOverflowInterval, ospfDemandExtensions } STATUS current DESCRIPTION "These objects are required for OSPF systems." ::= { ospfGroups 1 } ospfAreaGroup OBJECT-GROUP OBJECTS { ospfAreaId, ospfImportAsExtern, ospfSpfRuns, ospfAreaBdrRtrCount, ospfAsBdrRtrCount, ospfAreaLsaCount, ospfAreaLsaCksumSum, ospfAreaSummary, ospfAreaStatus } STATUS current DESCRIPTION "These objects are required for OSPF systems supporting areas." ::= { ospfGroups 2 } ospfStubAreaGroup OBJECT-GROUP OBJECTS { ospfStubAreaId, ospfStubTOS, ospfStubMetric, ospfStubStatus, ospfStubMetricType } STATUS current DESCRIPTION "These objects are required for OSPF systems supporting stub areas." ::= { ospfGroups 3 } Baker & Coltun Standards Track [Page 62] RFC 1850 OSPF MIB November 1995 ospfLsdbGroup OBJECT-GROUP OBJECTS { ospfLsdbAreaId, ospfLsdbType, ospfLsdbLsid, ospfLsdbRouterId, ospfLsdbSequence, ospfLsdbAge, ospfLsdbChecksum, ospfLsdbAdvertisement } STATUS current DESCRIPTION "These objects are required for OSPF systems that display their link state database." ::= { ospfGroups 4 } ospfAreaRangeGroup OBJECT-GROUP OBJECTS { ospfAreaRangeAreaId, ospfAreaRangeNet, ospfAreaRangeMask, ospfAreaRangeStatus, ospfAreaRangeEffect } STATUS obsolete DESCRIPTION "These objects are required for non-CIDR OSPF systems that support multiple areas." ::= { ospfGroups 5 } ospfHostGroup OBJECT-GROUP OBJECTS { ospfHostIpAddress, ospfHostTOS, ospfHostMetric, ospfHostStatus, ospfHostAreaID } STATUS current DESCRIPTION "These objects are required for OSPF systems that support attached hosts." ::= { ospfGroups 6 } Baker & Coltun Standards Track [Page 63] RFC 1850 OSPF MIB November 1995 ospfIfGroup OBJECT-GROUP OBJECTS { ospfIfIpAddress, ospfAddressLessIf, ospfIfAreaId, ospfIfType, ospfIfAdminStat, ospfIfRtrPriority, ospfIfTransitDelay, ospfIfRetransInterval, ospfIfHelloInterval, ospfIfRtrDeadInterval, ospfIfPollInterval, ospfIfState, ospfIfDesignatedRouter, ospfIfBackupDesignatedRouter, ospfIfEvents, ospfIfAuthType, ospfIfAuthKey, ospfIfStatus, ospfIfMulticastForwarding, ospfIfDemand } STATUS current DESCRIPTION "These objects are required for OSPF systems." ::= { ospfGroups 7 } ospfIfMetricGroup OBJECT-GROUP OBJECTS { ospfIfMetricIpAddress, ospfIfMetricAddressLessIf, ospfIfMetricTOS, ospfIfMetricValue, ospfIfMetricStatus } STATUS current DESCRIPTION "These objects are required for OSPF systems." ::= { ospfGroups 8 } ospfVirtIfGroup OBJECT-GROUP OBJECTS { ospfVirtIfAreaId, ospfVirtIfNeighbor, ospfVirtIfTransitDelay, Baker & Coltun Standards Track [Page 64] RFC 1850 OSPF MIB November 1995 ospfVirtIfRetransInterval, ospfVirtIfHelloInterval, ospfVirtIfRtrDeadInterval, ospfVirtIfState, ospfVirtIfEvents, ospfVirtIfAuthType, ospfVirtIfAuthKey, ospfVirtIfStatus } STATUS current DESCRIPTION "These objects are required for OSPF systems." ::= { ospfGroups 9 } ospfNbrGroup OBJECT-GROUP OBJECTS { ospfNbrIpAddr, ospfNbrAddressLessIndex, ospfNbrRtrId, ospfNbrOptions, ospfNbrPriority, ospfNbrState, ospfNbrEvents, ospfNbrLsRetransQLen, ospfNbmaNbrStatus, ospfNbmaNbrPermanence, ospfNbrHelloSuppressed } STATUS current DESCRIPTION "These objects are required for OSPF systems." ::= { ospfGroups 10 } ospfVirtNbrGroup OBJECT-GROUP OBJECTS { ospfVirtNbrArea, ospfVirtNbrRtrId, ospfVirtNbrIpAddr, ospfVirtNbrOptions, ospfVirtNbrState, ospfVirtNbrEvents, ospfVirtNbrLsRetransQLen, ospfVirtNbrHelloSuppressed } STATUS current DESCRIPTION Baker & Coltun Standards Track [Page 65] RFC 1850 OSPF MIB November 1995 "These objects are required for OSPF systems." ::= { ospfGroups 11 } ospfExtLsdbGroup OBJECT-GROUP OBJECTS { ospfExtLsdbType, ospfExtLsdbLsid, ospfExtLsdbRouterId, ospfExtLsdbSequence, ospfExtLsdbAge, ospfExtLsdbChecksum, ospfExtLsdbAdvertisement } STATUS current DESCRIPTION "These objects are required for OSPF systems that display their link state database." ::= { ospfGroups 12 } ospfAreaAggregateGroup OBJECT-GROUP OBJECTS { ospfAreaAggregateAreaID, ospfAreaAggregateLsdbType, ospfAreaAggregateNet, ospfAreaAggregateMask, ospfAreaAggregateStatus, ospfAreaAggregateEffect } STATUS current DESCRIPTION "These objects are required for OSPF systems." ::= { ospfGroups 13 } END 4. OSPF Traps OSPF is an event driven routing protocol, where an event can be a change in an OSPF interface's link-level status, the expiration of an OSPF timer or the reception of an OSPF protocol packet. Many of the actions that OSPF takes as a result of these events will result in a change of the routing topology. As routing topologies become large and complex it is often difficult to locate the source of a topology change or unpredicted routing path by polling a large number or routers. Another approach is to notify a network manager of potentially critical OSPF events with SNMP traps. Baker & Coltun Standards Track [Page 66] RFC 1850 OSPF MIB November 1995 This section defines a set of traps, objects and mechanisms to enhance the ability to manage IP internetworks which use OSPF as its IGP. It is an optional but useful extension to the OSPF MIB. 4.1. Format Of Trap Definitions Section 7 contains contains the trap definitions. 4.2. Approach The mechanism for sending traps is straight-forward. When an exception event occurs, the application notifies the local agent who sends a trap to the appropriate SNMP management stations. The message includes the trap type and may include a list of trap specific variables. A new object is defined in section 3.2 that will allow a network manager to enable or disable particular OSPF traps. Section 5 gives the trap definitions which includes the variable lists. The router ID of the originator of the trap is included in the variable list so that the network manager may easily determine the source of the trap. To limit the frequency of OSPF traps, the following additional mechanisms are suggested. 4.3. Ignoring Initial Activity The majority of critical events occur when OSPF is enabled on a router, at which time the designated router is elected and neighbor adjacencies are formed. During this initial period a potential flood of traps is unnecessary since the events are expected. To avoid unnecessary traps, a router should not originate expected OSPF interface related traps until two of that interface's dead timer intervals have elapsed. The expected OSPF interface traps are ospfIfStateChange, ospfVirtIfStateChange, ospfNbrStateChange, ospfVirtNbrStateChange, ospfTxRetranmit and ospfVirtIfTxRetransmit. Additionally, ospfMaxAgeLsa and ospfOriginateLsa traps should not be originated until two dead timer intervals have elapsed where the dead timer interval used should be the dead timer with the smallest value. 4.4. Throttling Traps The mechanism for throttling the traps is similar to the mechanism explained in RFC 1224 [11], section 5. The basic idea is that there is a sliding window in seconds and an upper bound on the number of traps that may be generated within this window. Unlike RFC 1224, traps are not sent to inform the network manager that the throttling mechanism has kicked in. Baker & Coltun Standards Track [Page 67] RFC 1850 OSPF MIB November 1995 A single window should be used to throttle all OSPF traps types except for the ospfLsdbOverflow and the ospfLsdbApproachingOverflow trap which should not be throttled. For example, if the window time is 3, the upper bound is 3 and the events that would cause trap types 1,3,5 and 7 occur within a 3 second period, the type 7 trap should not be generated. Appropriate values are 7 traps with a window time of 10 seconds. 4.5. One Trap Per OSPF Event Several of the traps defined in section 5 are generated as the result of finding an unusual condition while parsing an OSPF packet or a processing a timer event. There may be more than one unusual condition detected while handling the event. For example, a link- state update packet may contain several retransmitted link-state advertisements (LSAs), or a retransmitted database description packet may contain several database description entries. To limit the number of traps and variables, OSPF should generate at most one trap per OSPF event. Only the variables associated with the first unusual condition should be included with the trap. Similarly, if more than one type of unusual condition is encountered while parsing the packet, only the first event will generate a trap. 4.6. Polling Event Counters Many of the tables in the OSPF MIB contain generalized event counters. By enabling the traps defined in this document a network manager can obtain more specific information about these events. A network manager may want to poll these event counters and enable specific OSPF traps when a particular counter starts increasing abnormally. The following table shows the relationship between the event counters defined in the OSPF MIB and the trap types defined in section 5. Counter32 Trap Type ----------------------- ------------------------ ospfOriginateNewLsas ospfOriginateLsa ospfIfEvents ospfIfStateChange ospfConfigError ospfIfAuthFailure ospfRxBadPacket ospfTxRetransmit ospfVirtIfEvents ospfVirtIfStateChange ospfVirtIfConfigError ospfVirtIfAuthFailure Baker & Coltun Standards Track [Page 68] RFC 1850 OSPF MIB November 1995 ospfVirtIfRxBadPacket ospfVirtIfTxRetransmit ospfNbrEvents ospfNbrStateChange ospfVirtNbrEvents ospfVirtNbrStateChange ospfExternLSACount ospfLsdbApproachingOverflow ospfExternLSACount ospfLsdbOverflow 5. OSPF Trap Definitions OSPF-TRAP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, IpAddress FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ospfRouterId, ospfIfIpAddress, ospfAddressLessIf, ospfIfState, ospfVirtIfAreaId, ospfVirtIfNeighbor, ospfVirtIfState, ospfNbrIpAddr, ospfNbrAddressLessIndex, ospfNbrRtrId, ospfNbrState, ospfVirtNbrArea, ospfVirtNbrRtrId, ospfVirtNbrState, ospfLsdbType, ospfLsdbLsid, ospfLsdbRouterId, ospfLsdbAreaId, ospfExtLsdbLimit, ospf FROM OSPF-MIB; ospfTrap MODULE-IDENTITY LAST-UPDATED "9501201225Z" -- Fri Jan 20 12:25:50 PST 1995 ORGANIZATION "IETF OSPF Working Group" CONTACT-INFO " Fred Baker Postal: Cisco Systems 519 Lado Drive Santa Barbara, California 93111 Tel: +1 805 681 0115 E-Mail: fred@cisco.com Rob Coltun Postal: RainbowBridge Communications Tel: (301) 340-9416 E-Mail: rcoltun@rainbow-bridge.com" DESCRIPTION "The MIB module to describe traps for the OSPF Version 2 Protocol." ::= { ospf 16 } -- Trap Support Objects -- The following are support objects for the OSPF traps. Baker & Coltun Standards Track [Page 69] RFC 1850 OSPF MIB November 1995 ospfTrapControl OBJECT IDENTIFIER ::= { ospfTrap 1 } ospfTraps OBJECT IDENTIFIER ::= { ospfTrap 2 } ospfSetTrap OBJECT-TYPE SYNTAX OCTET STRING (SIZE(4)) MAX-ACCESS read-write STATUS current DESCRIPTION "A four-octet string serving as a bit map for the trap events defined by the OSPF traps. This object is used to enable and disable specific OSPF traps where a 1 in the bit field represents enabled. The right-most bit (least significant) represents trap 0." ::= { ospfTrapControl 1 } ospfConfigErrorType OBJECT-TYPE SYNTAX INTEGER { badVersion (1), areaMismatch (2), unknownNbmaNbr (3), -- Router is Dr eligible unknownVirtualNbr (4), authTypeMismatch(5), authFailure (6), netMaskMismatch (7), helloIntervalMismatch (8), deadIntervalMismatch (9), optionMismatch (10) } MAX-ACCESS read-only STATUS current DESCRIPTION "Potential types of configuration conflicts. Used by the ospfConfigError and ospfConfigVir- tError traps." ::= { ospfTrapControl 2 } ospfPacketType OBJECT-TYPE SYNTAX INTEGER { hello (1), dbDescript (2), lsReq (3), lsUpdate (4), lsAck (5) } MAX-ACCESS read-only STATUS current DESCRIPTION Baker & Coltun Standards Track [Page 70] RFC 1850 OSPF MIB November 1995 "OSPF packet types." ::= { ospfTrapControl 3 } ospfPacketSrc OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of an inbound packet that can- not be identified by a neighbor instance." ::= { ospfTrapControl 4 } -- Traps ospfIfStateChange NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfIfIpAddress, ospfAddressLessIf, ospfIfState -- The new state } STATUS current DESCRIPTION "An ospfIfStateChange trap signifies that there has been a change in the state of a non-virtual OSPF interface. This trap should be generated when the interface state regresses (e.g., goes from Dr to Down) or progresses to a terminal state (i.e., Point-to-Point, DR Other, Dr, or Backup)." ::= { ospfTraps 16 } ospfVirtIfStateChange NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfVirtIfAreaId, ospfVirtIfNeighbor, ospfVirtIfState -- The new state } STATUS current DESCRIPTION "An ospfIfStateChange trap signifies that there has been a change in the state of an OSPF vir- tual interface. Baker & Coltun Standards Track [Page 71] RFC 1850 OSPF MIB November 1995 This trap should be generated when the inter- face state regresses (e.g., goes from Point- to-Point to Down) or progresses to a terminal state (i.e., Point-to-Point)." ::= { ospfTraps 1 } ospfNbrStateChange NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfNbrIpAddr, ospfNbrAddressLessIndex, ospfNbrRtrId, ospfNbrState -- The new state } STATUS current DESCRIPTION "An ospfNbrStateChange trap signifies that there has been a change in the state of a non- virtual OSPF neighbor. This trap should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., 2-Way or Full). When an neighbor transitions from or to Full on non-broadcast multi-access and broadcast networks, the trap should be gen- erated by the designated router. A designated router transitioning to Down will be noted by ospfIfStateChange." ::= { ospfTraps 2 } ospfVirtNbrStateChange NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfVirtNbrArea, ospfVirtNbrRtrId, ospfVirtNbrState -- The new state } STATUS current DESCRIPTION "An ospfIfStateChange trap signifies that there has been a change in the state of an OSPF vir- tual neighbor. This trap should be generated when the neighbor state regresses (e.g., goes from Attempt or Full to 1-Way or Down) or progresses to a terminal state (e.g., Full)." ::= { ospfTraps 3 } Baker & Coltun Standards Track [Page 72] RFC 1850 OSPF MIB November 1995 ospfIfConfigError NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfIfIpAddress, ospfAddressLessIf, ospfPacketSrc, -- The source IP address ospfConfigErrorType, -- Type of error ospfPacketType } STATUS current DESCRIPTION "An ospfIfConfigError trap signifies that a packet has been received on a non-virtual in- terface from a router whose configuration parameters conflict with this router's confi- guration parameters. Note that the event op- tionMismatch should cause a trap only if it prevents an adjacency from forming." ::= { ospfTraps 4 } ospfVirtIfConfigError NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfVirtIfAreaId, ospfVirtIfNeighbor, ospfConfigErrorType, -- Type of error ospfPacketType } STATUS current DESCRIPTION "An ospfConfigError trap signifies that a pack- et has been received on a virtual interface from a router whose configuration parameters conflict with this router's configuration parameters. Note that the event optionMismatch should cause a trap only if it prevents an ad- jacency from forming." ::= { ospfTraps 5 } ospfIfAuthFailure NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfIfIpAddress, ospfAddressLessIf, ospfPacketSrc, -- The source IP address ospfConfigErrorType, -- authTypeMismatch or Baker & Coltun Standards Track [Page 73] RFC 1850 OSPF MIB November 1995 -- authFailure ospfPacketType } STATUS current DESCRIPTION "An ospfIfAuthFailure trap signifies that a packet has been received on a non-virtual in- terface from a router whose authentication key or authentication type conflicts with this router's authentication key or authentication type." ::= { ospfTraps 6 } ospfVirtIfAuthFailure NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfVirtIfAreaId, ospfVirtIfNeighbor, ospfConfigErrorType, -- authTypeMismatch or -- authFailure ospfPacketType } STATUS current DESCRIPTION "An ospfVirtIfAuthFailure trap signifies that a packet has been received on a virtual interface from a router whose authentication key or au- thentication type conflicts with this router's authentication key or authentication type." ::= { ospfTraps 7 } ospfIfRxBadPacket NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfIfIpAddress, ospfAddressLessIf, ospfPacketSrc, -- The source IP address ospfPacketType } STATUS current DESCRIPTION "An ospfIfRxBadPacket trap signifies that an OSPF packet has been received on a non-virtual interface that cannot be parsed." ::= { ospfTraps 8 } Baker & Coltun Standards Track [Page 74] RFC 1850 OSPF MIB November 1995 ospfVirtIfRxBadPacket NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfVirtIfAreaId, ospfVirtIfNeighbor, ospfPacketType } STATUS current DESCRIPTION "An ospfRxBadPacket trap signifies that an OSPF packet has been received on a virtual interface that cannot be parsed." ::= { ospfTraps 9 } ospfTxRetransmit NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfIfIpAddress, ospfAddressLessIf, ospfNbrRtrId, -- Destination ospfPacketType, ospfLsdbType, ospfLsdbLsid, ospfLsdbRouterId } STATUS current DESCRIPTION "An ospfTxRetransmit trap signifies than an OSPF packet has been retransmitted on a non- virtual interface. All packets that may be re- transmitted are associated with an LSDB entry. The LS type, LS ID, and Router ID are used to identify the LSDB entry." ::= { ospfTraps 10 } ospfVirtIfTxRetransmit NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfVirtIfAreaId, ospfVirtIfNeighbor, ospfPacketType, ospfLsdbType, ospfLsdbLsid, ospfLsdbRouterId } STATUS current Baker & Coltun Standards Track [Page 75] RFC 1850 OSPF MIB November 1995 DESCRIPTION "An ospfTxRetransmit trap signifies than an OSPF packet has been retransmitted on a virtual interface. All packets that may be retransmit- ted are associated with an LSDB entry. The LS type, LS ID, and Router ID are used to identify the LSDB entry." ::= { ospfTraps 11 } ospfOriginateLsa NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfLsdbAreaId, -- 0.0.0.0 for AS Externals ospfLsdbType, ospfLsdbLsid, ospfLsdbRouterId } STATUS current DESCRIPTION "An ospfOriginateLsa trap signifies that a new LSA has been originated by this router. This trap should not be invoked for simple refreshes of LSAs (which happesn every 30 minutes), but instead will only be invoked when an LSA is (re)originated due to a topology change. Addi- tionally, this trap does not include LSAs that are being flushed because they have reached MaxAge." ::= { ospfTraps 12 } ospfMaxAgeLsa NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfLsdbAreaId, -- 0.0.0.0 for AS Externals ospfLsdbType, ospfLsdbLsid, ospfLsdbRouterId } STATUS current DESCRIPTION "An ospfMaxAgeLsa trap signifies that one of the LSA in the router's link-state database has aged to MaxAge." ::= { ospfTraps 13 } Baker & Coltun Standards Track [Page 76] RFC 1850 OSPF MIB November 1995 ospfLsdbOverflow NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfExtLsdbLimit } STATUS current DESCRIPTION "An ospfLsdbOverflow trap signifies that the number of LSAs in the router's link-state data- base has exceeded ospfExtLsdbLimit." ::= { ospfTraps 14 } ospfLsdbApproachingOverflow NOTIFICATION-TYPE OBJECTS { ospfRouterId, -- The originator of the trap ospfExtLsdbLimit } STATUS current DESCRIPTION "An ospfLsdbApproachingOverflow trap signifies that the number of LSAs in the router's link- state database has exceeded ninety percent of ospfExtLsdbLimit." ::= { ospfTraps 15 } -- conformance information ospfTrapConformance OBJECT IDENTIFIER ::= { ospfTrap 3 } ospfTrapGroups OBJECT IDENTIFIER ::= { ospfTrapConformance 1 } ospfTrapCompliances OBJECT IDENTIFIER ::= { ospfTrapConformance 2 } -- compliance statements ospfTrapCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement " MODULE -- this module MANDATORY-GROUPS { ospfTrapControlGroup } GROUP ospfTrapControlGroup DESCRIPTION "This group is optional but recommended for all OSPF systems" Baker & Coltun Standards Track [Page 77] RFC 1850 OSPF MIB November 1995 ::= { ospfTrapCompliances 1 } -- units of conformance ospfTrapControlGroup OBJECT-GROUP OBJECTS { ospfSetTrap, ospfConfigErrorType, ospfPacketType, ospfPacketSrc } STATUS current DESCRIPTION "These objects are required to control traps from OSPF systems." ::= { ospfTrapGroups 1 } END 6. Acknowledgements This document was produced by the OSPF Working Group. 7. References [1] Cerf, V., "IAB Recommendations for the Development of Internet Network Management Standards", RFC 1052, NRI, April 1988. [2] Cerf, V., "Report of the Second Ad Hoc Network Management Review Group", RFC 1109, NRI, August 1989. [3] Rose M., and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based internets", STD 16, RFC 1155, Performance Systems International, Hughes LAN Systems, May 1990. [4] McCloghrie K., and M. Rose, "Management Information Base for Network Management of TCP/IP-based internets", RFC 1156, Hughes LAN Systems, Performance Systems International, May 1990. [5] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, SNMP Research, Performance Systems International, Performance Systems International, MIT Laboratory for Computer Science, May 1990. Baker & Coltun Standards Track [Page 78] RFC 1850 OSPF MIB November 1995 [6] Rose M., Editor, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, Performance Systems International, March 1991. [7] Information processing systems - Open Systems Interconnection - Specification of Abstract Syntax Notation One (ASN.1), International Organization for Standardization, International Standard 8824, December 1987. [8] Information processing systems - Open Systems Interconnection - Specification of Basic Encoding Rules for Abstract Notation One (ASN.1), International Organization for Standardization, International Standard 8825, December 1987. [9] Rose, M., and K. McCloghrie, Editors, "Concise MIB Definitions", STD 16, RFC 1212, Performance Systems International, Hughes LAN Systems, March 1991. [10] Rose, M., Editor, "A Convention for Defining Traps for use with the SNMP", RFC 1215, Performance Systems International, March 1991. [11] Steinberg, L., "Techniques for Managing Asynchronously Generated Alerts", RFC 1224, IBM Corporation, May 1991. [12] Moy, J., "Multicast Extensions to OSPF", RFC 1584, Proteon, Inc., September 1993. Baker & Coltun Standards Track [Page 79] RFC 1850 OSPF MIB November 1995 8. Security Considerations Security issues are not discussed in this memo. 9. Authors' Addresses Fred Baker cisco Systems, Inc. 519 Lado Drive Santa Barbara, CA 93111 Phone: (805) 681-0115 EMail: fred@cisco.com Rob Coltun RainbowBridge Communications Phone: (301) 340-9416 EMail: rcoltun@rainbow-bridge.com Baker & Coltun Standards Track [Page 80]

[Contrib] [RFC Index] [RFC 1800 - 1899]    RFC 1850: OSPF Version 2 Management Information Base